Make and hold this extremely easy jig for good notches with out all of the measuring.
Right here’s a cool trick for slicing a bunch of equivalent notches with no dado stack. Rigorously reduce an correct notch from the top of a board, precisely the identical dimension as your required notch. Connect a clamp board to the opposite finish of the notched board and clamp the meeting to your noticed’s fence. Mark the notch location in your workpiece and set the fence. The jig’s finish registers the primary minimize. Slip the workpiece into the notch for the second minimize, after which make a number of passes to clear the remaining waste. – Craig Harper. Additionally take a look at our desk noticed ideas and methods right here.
Take a look at another dirt-simple jigs it is best to know:
Drill Press Desk
Many drill press tables are too small for woodworking as a result of they have been designed for metalworking. Additionally, normal drill press tables do not have a fence or an insert to again up holes drilled all through a bit of wooden. This jig solves these issues! Make the desk from three layers of 1/2-in. medium-density fiberboard glued collectively. It is fixed to the machine’s desk from beneath with 4 lag screws. The desk’s prime layer consists of three items. The outer items are glued to the desk, whereas the middle piece—the insert—is unfastened. The insert is 1/Eight in. narrower than the hole between the 2 outer items. Set up three flat-head screws within the aspect of the insert and adjusted them so the insert matches comfortable within the hole. Once you want a recent floor to drill into, slide the insert in or out, flip it round or flip it over. Additionally, make a number of additional inserts so you’ll be able to toss one away when it begins wanting like Swiss cheese. The fence is only a plain board clamped to the desk.
Jig for Routing Dadoes
When constructing a cupboard, dadoes are sometimes used to make sure that cabinets and partitions are spaced appropriately. To make a robust joint, the width of the dadoes should precisely match the thickness of the plywood. That may be a problem as a result of few items of plywood are exactly Three/Four in. thick. They’re often 1/32 in. or so lower than the “nominal” thickness. This jig will rout perfect-fitting dadoes for any piece of three/Four-in. plywood no matter its precise thickness. Use a particular top-bearing trim router bit with the jig. The bit is 1/2 in. extensive, half in. lengthy and has a bearing mounted above the cutter. The bearing is flush with the bit’s chopping edges. This routing jig has two lengthy, parallel guides produced from 1/2-in. MDF. Once you rout a dado, experience the bearing alongside one information, then make a second, return move and journey the bearing alongside the second information. This manner, the area between the guides determines the width of the dado. Establishing the guides is straightforward. One information is fastened to the jig’s Three/Four-in. cross members; the opposite is unfastened and adjustable. Take two small items of the plywood and place them towards the fastened information. Then slide the adjustable information towards the items and clamp the information to the cross members. Achieved!
Learn how to make use of a pocket screw jig, too, within the video under.[rd-video id=”43633″]
Sacrificial Desk Noticed Fence
When you must regulate the desk noticed’s fence so it sits proper subsequent to the blade, put a “sacrificial” fence on the noticed. Utilizing a sacrificial fence helps you keep away from by accident chopping into the actual fence, which might be actually dangerous information. This sacrificial fence is made of 4 thicknesses of 1/2-in. MDF glued collectively. (Threequarter- inch plywood would work simply as nicely.) Minimize the center items into thirds in an effort to create holes for clamping. The holes be sure that the clamp’s heads will not get in the best way once you’re making a minimize. The great thing about this technique is that you need to use all sides of the fence till it wears out—however it’s straightforward to make one other!
Desk Noticed Information Field
No-Wiggle Desk Noticed Crosscuts
In case your miter gauge’s bar wiggles within the noticed’s miter slot, you will have a tough time getting a completely straight crosscut. This is a solution to repair that: Use two miter gauges related by a fence. An additional miter gauge is not very costly, however you’ll be able to reduce the fee to zero by making one your self. Glue two items of Baltic birch plywood collectively to type an L-shape physique, then rigorously minimize a bar to suit snugly into your noticed’s miter slot. Use a bit of maple to make the bar, or 1/Four-in. tempered hardboard is one other good selection. Glue the bar to the physique utilizing spring clamps, so you possibly can simply regulate the bar to be precisely 90 levels to the physique earlier than the glue units. Set up screws later. You in all probability will not be capable of use your noticed’s guard with this setup, so it is a good suggestion so as to add a plastic defend to the fence. The defend will remind you to not put your fingers too near the blade and can maintain the sawdust out of your eyes.
Increase Your Vise’s Holding Energy
Once you clamp a board utilizing just one aspect of your vise, have you ever observed that the board typically slips or rotates should you push down on it? That is as a result of the vise’s jaws don’t remain parallel when the vise is tightened. Your board is getting pinched solely alongside one edge. Even the perfect vises “rack” like this. Fixing the issue is sort of easy. You simply want to put a spacer on the other aspect of the vise. The spacer must be the identical thickness as your workpiece—a scrap offcut works properly. Drive a screw into one finish of the spacer or pinch it with a spring clamp so you do not have to carry on to the spacer whereas tightening the vise.
Additional-Giant Sander Desk
Benchtop disc sanders include small tables. When you want a bigger desk, make a brand new one and clamp it to the unique desk. At first you may assume you will add the extra-large desk solely if you want it, however as soon as you set it on, you may by no means take it off! This jig is way fancier than it needs to be—a plain piece of melamine would have sufficed.
A cupboard that is out of sq. is sort of a home constructed on a basis that is not degree. Good luck getting doorways to hold proper! Once you glue and clamp up a case, use a few “squaring blocks” to ensure the case has 90-degree corners. Clamp the blocks to the case earlier than placing the ultimate squeeze on the case’s clamps. Such a squaring block could be very straightforward to make. First, reduce a bit of plywood about Eight in. sq.. (Be sure the within nook is actually sq. by testing it with a mixture sq..) Subsequent, screw two Three/Four-in. x 2-Three/Four-in. x 7-in. lips to adjoining sides of the block for clamping. Depart a niche on the inside nook of the block so you possibly can take away glue that squeezes out of the joint.
Three-Layer Gap Drilling Spacer
You could have seen this trick earlier than—utilizing a bit of pegboard to drill evenly spaced holes for shelf pins. However this is one other tackle it: Make the jig from three layers of pegboard. A thick jig has a few benefits. First, the holes will not put on out as quick (holes in a single layer of pegboard are likely to grow to be oval shortly). Second, the extra thickness will assist hold your drill perpendicular to the panel. When utilizing the jig, tape over the holes you do not want so you do not make a dumb mistake. Additionally, slide a wooden block onto the drill bit to restrict the opening depth. So, how do you retain the holes aligned when gluing the items collectively? It is actually fairly easy. Insert a few 1/Four-in. machine bolts by means of reverse ends of the glue-up, then add washers and nuts. Tightening the nuts will pressure the items into alignment and maintain them there. Trim the sides of the jig after the glue dries.
Correct Miter Noticed Cuts
Clamp this small Baltic birch desk to your miter noticed if you need to minimize a number of brief items to a precise size. The slot within the desk’s fence exhibits you exactly the place the blade will minimize—simply mark the piece with a pencil and line up the mark with the slot. The slot has “zero clearance,” which means there isn’t any hole on both aspect of the blade. The slot within the desk is zero clearance too. Zero-clearance slots scale back tear-out to an absolute minimal, eliminating splintered edges. When this desk was made, the fence was one lengthy piece of wooden. Cleats have been screwed to the desk’s ends to lock the desk in place. Then the noticed was lowered to chop the slot within the fence. Word that the desk have to be wider than the noticed’s turntable—the uncut portion of the desk is what holds it collectively!
Add an adjustable fence to your drill press to make it so much handier for woodworking tasks! A fence is particularly helpful for drilling rows of exactly positioned holes. Additionally, boring holes in a small workpiece is a snap—simply clamp the piece to the fence at any angle and drill the opening. You gained’t wrestle with holding small items in place when you drill. (That’s additionally harmful!)
1. Connect a 2-ft. x 1-ft. scrap of plywood or particleboard to the drill press desk with countersunk 1/Four-in. flat head machine screws, fender washers and nuts. (Run the screws via the slots within the metallic desk. The fender washers will span the slots.)
2. Create the fence from a 2 ft. x Four-in. x 1-in. board bolted to a 2-ft. piece of Three-in. x 1/Eight-in. aluminum angle iron ($10 at a house middle for a Four-ft. size). Once more, countersink the holes within the board earlier than bolting the board to the angle iron.
Vertical Drilling Jig
In case you’ve ever tried to drill a wonderfully straight and centered deep gap in the long run of a board, you already know that it’s almost unattainable with a handheld drill. However add a drill press and a jig and the job turns into very doable. Make this jig from two Eight-in. x 12-in. items of three/Four-in. plywood or medium-density fiberboard (MDF). Simply screw the items collectively to type a “T” and reinforce the jig with a few triangles.
To make use of the jig, clamp it to the drill press desk and the workpiece to the jig. Draw an “X” throughout the corners to seek out the precise middle of the piece. You’ll have to regulate the peak of the desk and pivot it till you line all the things up, however after that, drilling a straight, centered gap is a cinch. This trick will work for rectangular or sq. boards.
Reduce Slender Strips with a Sliding Jig
To make a collection of similar slender strips for shelf edging, you need not take away the blade guard or transfer the fence for each reduce. Simply connect a brief strip of wooden barely thinner than the width of the rip reduce to the top of a Four-ft. 1×6. Then maintain the board towards it and push the jig by means of. The jig retains your arms properly away from the blade, and you may rip as many items as you want with out ever shifting the fence.
To make the jig, connect a 5-in.-long strip of wooden, 1/16 in. narrower than the width of the specified rip, to the top of a 1×6 as proven. Principally you are making a horizontal push stick. Add a deal with close to the top of the jig to offer your self higher management as you run the jig by way of the noticed.